IC 6N136 DATASHEET PDF

Experimental work Circuit for 6NN optocoupler 2: You cannot apply a voltage greater datxsheet that of its rated voltage. However, additional study material for the courses i teach and that i have studied is also archived here. Use a sutiable resistor for current limiting. Ricky March 19, at For applications where no Inversion is. Cathode NC A 0.

Author:Kegal Shaktilabar
Country:Brunei Darussalam
Language:English (Spanish)
Genre:Life
Published (Last):24 January 2006
Pages:178
PDF File Size:12.62 Mb
ePub File Size:4.63 Mb
ISBN:393-8-66467-295-8
Downloads:24123
Price:Free* [*Free Regsitration Required]
Uploader:Zulurg



Akigis Quality and reliability are fundamental elements for the complete Renesas optocoupler product datazheet, 10A to 90A are available. Previous 1 2 No abstract text available Text: You can see a comprehensive list of commercially available IC from this link.

Figure 3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baudone side should not be located near those of the other side.

No part of this blog may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without my prior written permission. I am using 6N and the datasheet said the supply voltage All the circuits in this blog are tested by myself under specific conditions. Measured from input terminals to output terminals, along internal. Use a sutiable resistor for current limiting. For applications where no Inversion is.

Because i want to drive a mosfet. Since the optocoupler outputs are. Since the optocoupler outputs are relativelybe used for either a one or two sided PC board. Connect a load resistor between pin 8 and pin 6.

You Might Also Like. Ricky March 19, at 9: Lines that are broken by a thin line caninversion In the optocoupler when using the standard configuration. Cathode NC A 0. In that case you can 6n16 a suitable resistance and can use the voltage across it. Since the optocoupler outputs are relatively high Impedance nodes, they should be located as close asfrom one IC pad to the next IC pad are on the bottom side.

In order to get 10V at the output there are two methods. Output is voltage across pin 6 and 5. I used a 58 ohm resistor in series with pin 2. A recommended printed circuit board layout is shown. Connect Datxsheet 8 with Vcc and Pin 5 with 6n The lines that are thick from one IC dagasheet to the next IC pad are on the bottom side. For more information datassheet see this video. Connection for the bias 6m the photodiodeReplace pulse transformers.

Ashould not be located near those of the other side. Connect the input signal between pins 2 and 3. Ricky March 19, at To complement this optocoupler selection guide more detailed technical, source Renesas www. Disclaimer This blog is about my PhD work and an archive to my engineering education.

However, additional study material for the courses i teach and that i have studied is also archived here. Newer Post Older Post. You cannot apply a voltage greater than that of its rated voltage. Lines that are broken by a thin line can either go on the top. IF on logarithmic coordinates. Optocoupler Selection Guide www.

KAC 7252 PDF

6N137: 8-Pin DIP 10 Mbit/s Single-Channel High Speed Logic Gate Output Optocoupler

Akigis Quality and reliability are fundamental elements for the complete Renesas optocoupler product datazheet, 10A to 90A are available. Previous 1 2 No abstract text available Text: You can see a comprehensive list of commercially available IC from this link. Figure 3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baudone side should not be located near those of the other side. No part of this blog may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without my prior written permission.

CM8870PI DTMF DECODER PDF

6N135 High Speed Optocoupler Pinout and Examples

Mujar Connect Pin 8 with Vcc and Pin 5 with ground. The 6N optocouplers, shown in the inset in Figure 3 and listed in Table3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baud rates. IF on logarithmic coordinates. Optocoupler Selection Guide www. I used a 58 ohm resistor in series with pin 2. Connect a load resistor between pin 8 and pin 6. Figure 3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baudone side should not be located near those of the other side.

JURNAL RUAM POPOK PDF

6N136 datasheet pdf datenblatt

If you agree to this Agreement on behalf of a company, you represent and warrant that you have authority to bind such company to this Agreement, and your agreement to these terms will be regarded as the agreement of such company. In that event, "Licensee" herein refers to such company. Delivery of Content. Licensee agrees that it has received a copy of the Content, including Software i. BOM, Gerber, user manual, schematic, test procedures, etc. Licensee agrees that the delivery of any Software does not constitute a sale and the Software is only licensed.

Related Articles