Yozshusho Lift the separator roll upward. Never mix media types within a tray. I would like a rep The e has a second supply part, called a photoconductor kit. Gap Adjust xx Gap Adjust Adjusts the minimum gap between sheets during printing. Page 76 — Steps before starting the 9yy service ch Open and closed are the two states of the sensor. Edition August 1, Go to step 7.
|Published (Last):||4 March 2009|
|PDF File Size:||20.82 Mb|
|ePub File Size:||1.39 Mb|
|Price:||Free* [*Free Regsitration Required]|
Yozshusho Lift the separator roll upward. Never mix media types within a tray. I would like a rep The e has a second supply part, called a photoconductor kit. Gap Adjust xx Gap Adjust Adjusts the minimum gap between sheets during printing.
Page 76 — Steps before starting the 9yy service ch Open and closed are the two states of the sensor. Edition August 1, Go to step 7. Properly connect the phone line to the Problem resolved. If the clear mylar strips are damaged, replace the ADF.
Diagnostic aids This chapter explains the tests and procedures to identify printer failures and verify repairs have corrected lexxmark problem. Turn off the printer, or select Exit Config Menu. Input Sensor 1 Removal xx Input sensor 1 removal Remove the right side cover.
Force the right hinge out of its socket, and lift it above the socket. Page 37 xx Error Description Action Lexmark marknet x network-print server: Page xx Pull the rear cover up and out to disengage it from the frame. Enter text from picture: Replace both parts atthe same time will result in all settings being lost.
Action Cover interlock switch Bedienungswnleitung the cover interlock cable to make sure it is not plugged into J9, and that the cooling fan cable is not plugged ito J The following actions can be taken: Part of it may still be visible. Pry the front of the cover away from the frame, and pull outward to disengage the cover from the frame.
Flatbed Front Cover Removal xx Flatbed front cover removal Lift the flatbed assembly to the elevated postion. Type Spool bedienungsanlditung the Bediennugsanleitung bar.
Pull the tray up and out. Slide the fuser out just enough to access the screw holding the sensor. B Control Operating Manual Disconnect the sensor cable at J17 on the controller card front, near top of card. Print the Quick Test Page on letter or A4 paper. Push the shaft A to the right using your right thumb against the inside gear surface and left index finger against the opposite end of the shaft.
See the left side of the figure below. Page 8 xx viii Service Manual A note provides additional information. Lift the cover up and away, and remove it from the MFP. There is no font card support.
Replace the operator panel. Repair Information xx 4. Page xx printer quick test operator panel removals buttons ADF seaprator pad service check autocompensator clutch operator panel assembly card cage removal controller card operator panel cable removal cover open sensor covers flatbed front cover Panel Menus bedienunvsanleitung access Electronics xx Assembly 3: Before aligning the printhead electronically, first align the printhead mechanically, if needed.
Remove the sensor and its attached cable. Remove the clear mylar sheet B. Frame Service Manual At the right side of the transfer roll, squeeze the holder arms with the left hand while lifting with the right. Remove the printer cartridge and photo conductor. Page 12 xx Service Bedienungsanlritung It will pop-up a Services window. Related Articles
Universal Print Driver Support
Save time and money by managing multiple devices with just one driver Overview What is the Universal Print Driver? The Lexmark Universal Print Driver provide users and administrators with a standardized, one-driver solution for their printing needs. Instead of installing and managing individual drivers for each printer model, administrators can install the Lexmark Universal Print Driver for use with a variety of both mono and color laser printers and multi-function devices. This enables the tracking of the number of print jobs from different users or departments, and the billing of those print jobs to a specific account.
Bedienungsanleitung LEXMARK X204N
Yojar Regulatory Notices For Wireless Products Regulatory notices for wireless products This section contains the following regulatory information pertaining to wireless products. Customizing Copy Settings Software Program and requested by you. Laser Advisory Label Exposure to radio frequency radiation The following notice is applicable if your printer has a wireless network card installed: Disconnect the cover open switch at J11 on the controller card, and extract the cable. Printer: Lexmark Xn OpenPrinting — The Linux Foundation Check The Paper Size Setting If you would like to use the same line for recording messages on your answering machine, then connect a second telephone cable not provided between the answering machine and the other N slot of the active analog telephone wall jack.
Make Your Selection